mirror of
https://codeberg.org/privacy1st/nix-git
synced 2024-11-24 22:29:33 +01:00
93 lines
4.5 KiB
Nix
93 lines
4.5 KiB
Nix
{ config, pkgs, ... }:
|
|
|
|
# hdparm - get/set SATA/IDE device parameters
|
|
# -q Handle the next option quietly, suppressing normal output (but not error messages).
|
|
# -I Print device information.
|
|
# -C Check the current IDE power mode status:
|
|
# unknown (drive does not support this command)
|
|
# active/idle (normal operation)
|
|
# standby (low power mode, drive has spun down)
|
|
# sleeping (lowest power mode, drive is completely shut down)
|
|
# -S Set the standby (spindown) timeout for the drive.
|
|
# The timeout specifies how long to wait in idle (with no disk activity) before turning off the motor to save power.
|
|
# The value of 0 disables spindown,
|
|
# the values from 1 to 240 specify multiples of 5 seconds
|
|
# and values from 241 to 251 specify multiples of 30 minutes.
|
|
# -y Force an IDE drive to immediately enter the low power consumption standby mode, usually causing it to spin down.
|
|
|
|
# Get power status:
|
|
# sudo hdparm -C /dev/disk/by-id/ata-WDC_WD40EFRX-68N32N0_WD-WCC7K0CPF0N1
|
|
# #=> drive state is: active/idle
|
|
#
|
|
# Spin down after 2 minutes (120s/5s = 24).
|
|
# TODO: Western Digital (WD) Red/Green drives don't work properly. For low `-S` values, they spin down after **10** minutes. And for high values they don't spin down at all.
|
|
# - https://superuser.com/questions/1746074/spin-down-not-working-on-wd-red
|
|
# - https://askubuntu.com/questions/196473/setting-sata-hdd-spindown-time-for-western-digital-green-drives
|
|
#
|
|
# sudo hdparm -S 24 /dev/disk/by-id/ata-WDC_WD40EFRX-68N32N0_WD-WCC7K0CPF0N1 # 4tb1
|
|
# sudo hdparm -S 24 /dev/disk/by-id/ata-WDC_WD30EFRX-68EUZN0_WD-WCC4N1173157 # 3tb1
|
|
# sudo hdparm -S 24 /dev/disk/by-id/ata-WDC_WD30EFRX-68EUZN0_WD-WMC4N0564095 # 3tb2
|
|
#
|
|
# ... after > 10 minutes ...
|
|
#
|
|
# Query disk without waking it up:
|
|
# https://wiki.archlinux.org/title/hdparm#Querying_the_status_of_the_disk_without_waking_it_up
|
|
# sudo smartctl -i -n standby /dev/disk/by-id/ata-WDC_WD40EFRX-68N32N0_WD-WCC7K0CPF0N1
|
|
# #=> Device is in STANDBY mode, exit(2)
|
|
#
|
|
# Get power status:
|
|
# sudo hdparm -C /dev/disk/by-id/ata-WDC_WD40EFRX-68N32N0_WD-WCC7K0CPF0N1
|
|
# sudo hdparm -C /dev/disk/by-id/ata-WDC_WD30EFRX-68EUZN0_WD-WCC4N1173157
|
|
# sudo hdparm -C /dev/disk/by-id/ata-WDC_WD30EFRX-68EUZN0_WD-WMC4N0564095
|
|
# #=> drive state is: standby
|
|
|
|
# Power savings.
|
|
# With 12tb1, 3tb1, 3tb2 spinning and 4tb1 spun-down: 26.1 W
|
|
# With 12tb1 spinning and 3tb1, 3tb2, 4tb1 spun-down: 19.8 W
|
|
# -> WD30EFRX measured idle spinning vs standby = +3.15 W
|
|
# -> WD30EFRX advertised idle spinning vs unplugged = +3.0 W
|
|
|
|
# See also: Systemd service to spin down after boot. https://wiki.archlinux.org/title/hdparm#Putting_a_drive_to_sleep_directly_after_boot
|
|
|
|
# TODO: For external (USB-)disks, use `hd-idle`.
|
|
# https://www.reddit.com/r/NixOS/comments/751i5t/comment/do3f3l7/
|
|
# # Options:
|
|
# # -a <disk>: Select disk for subsequent parameters.
|
|
# # -i 120: Spin down after 2 minutes (120 seconds) of inactivity.
|
|
# ExecStart = "${pkgs.hd-idle}/bin/hd-idle -a /dev/disk/by-id/XXX-XXX-XXX -i 120";
|
|
|
|
# Note about the `script` settings below.
|
|
# If the disk is spun-down (in standby mode):
|
|
# - The standby timeout has been set before already, otherwise it would be spinning.
|
|
# - Don't set the standby timeout again, as this will spin up the disk.
|
|
|
|
{
|
|
environment.systemPackages = with pkgs; [
|
|
hdparm
|
|
];
|
|
systemd.services."hdparm-4tb1" = {
|
|
description = "Spin down inactive HDD";
|
|
wantedBy = [ "multi-user.target" ];
|
|
serviceConfig.Type = "oneshot";
|
|
script = ''
|
|
${pkgs.hdparm}/bin/hdparm -C /dev/disk/by-id/ata-WDC_WD40EFRX-68N32N0_WD-WCC7K0CPF0N1 | ${pkgs.busybox}/bin/grep 'standby' || ${pkgs.hdparm}/bin/hdparm -S 24 /dev/disk/by-id/ata-WDC_WD40EFRX-68N32N0_WD-WCC7K0CPF0N1
|
|
'';
|
|
};
|
|
systemd.services."hdparm-3tb1" = {
|
|
description = "Spin down inactive HDD";
|
|
wantedBy = [ "multi-user.target" ];
|
|
serviceConfig.Type = "oneshot";
|
|
script = ''
|
|
${pkgs.hdparm}/bin/hdparm -C /dev/disk/by-id/ata-WDC_WD30EFRX-68EUZN0_WD-WCC4N1173157 | ${pkgs.busybox}/bin/grep 'standby' || ${pkgs.hdparm}/bin/hdparm -S 24 /dev/disk/by-id/ata-WDC_WD30EFRX-68EUZN0_WD-WCC4N1173157
|
|
'';
|
|
};
|
|
systemd.services."hdparm-3tb2" = {
|
|
description = "Spin down inactive HDD";
|
|
wantedBy = [ "multi-user.target" ];
|
|
serviceConfig.Type = "oneshot";
|
|
script = ''
|
|
${pkgs.hdparm}/bin/hdparm -C /dev/disk/by-id/ata-WDC_WD30EFRX-68EUZN0_WD-WMC4N0564095 | ${pkgs.busybox}/bin/grep 'standby' || ${pkgs.hdparm}/bin/hdparm -S 24 /dev/disk/by-id/ata-WDC_WD30EFRX-68EUZN0_WD-WMC4N0564095
|
|
'';
|
|
};
|
|
}
|